The oil pressure at the pump outlet, which is what opens the pressure relief valve, is simply the resistance to flow caused by the bearing clearances and restrictions.

    The oil pressure gauge, or warning lamp, gives only the pressure at the point where its sender enters that part of the pressurized system – not everywhere, not an average, nor a generalized picture of the systemic pressure.

    Despite the frequent comparison to hydraulic engineering theory, this is not a “closed system” in which oil pressure is balanced and identical everywhere. All engines are “open systems”, because the oil returns to the pan by a series of controlled leaks. The bearings farthest from the pump always have the lowest pressure because of the number of leaks between the pump and that bearing. Excess bearing clearance increases the pressure loss between the first and last bearing in a series.

    Depending on condition, an engine may have acceptable gauge pressure, and still only 5 psi pressure at one connecting rod, which will fail under high load.

    The pressure is actually created by the resistance to the flow of the oil around the engine.[5] So, the pressure of the oil may vary during operation, with temperature, engine speed, and wear on the engine. Colder oil temperature can cause higher pressure, as the oil is thicker, while higher engine speeds cause the pump to run faster and push more oil through the engine. Because of variances in temperature and normal higher engine speed upon cold engine start up, it’s normal to see higher oil pressure upon engine start up than at normal operating temperatures, where normal oil pressure usually falls between 30 and 45 psi.[6] Too much oil pressure can create unnecessary work for the engine and even add air into the system. To ensure that the oil pressure does not exceed the rated maximum, once pressure exceeds a preset limit a spring-loaded pressure relief valve dumps excess pressure either to the suction side of the pump, or directly back to the oil pan or tank.

    High oil pressure frequently means extremely high pressure on cold start-up, but this is a design flaw rather than an automatic consequence of high pressure. The observation “if you raise the maximum pressure, the cold pressure goes too high” is accurate, but not intentional.
Even the stock pumps (regardless of brand and model) do not have enough relief valve capacity: the relief port is too small to handle the volume of cold oil. This is why there is a significant difference between cold & hot oil, high & low RPM, &c., but it’s typically not a problem with stock engines. A correctly designed relief port (which is not found in production engines) will flow any oil volume the gears will pass, regardless of oil viscosity or temperature, and the gauge reading will only vary slightly.

    The oil pressure is monitored by an oil pressure sending unit, usually mounted to the block of the engine. This can either be a spring-loaded pressure sensor or an electronic pressure sensor, depending on the type of sending unit. Problems with the oil pressure sending unit or the connections between it and the driver's display can cause abnormal oil pressure readings when oil pressure is perfectly acceptable.

Low Oil Pressure
    Low oil pressure, however, can cause engine damage. Low oil pressure can be caused by many things, such as a faulty oil pump, a clogged oil pickup screen, excessive wear on high mileage engines, or simply low oil volume. Indications of low oil pressure may be that the warning light is on, a low pressure reading on the gauge, or clattering/clinking noises from the engine. Low oil pressure is a problem that must be addressed immediately to prevent serious damage.

    The leading cause of low oil pressure in an engine is wear on the engine’s vital parts. Over time, engine bearings and seals suffer from wear and tear. Wear can cause these parts to eventually lose their original dimensions, and this increased clearance allows for a greater volume of oil to flow over time which can greatly reduce oil pressure. For instance, .001 of an inch worn off of the engine’s main bearings can cause up to a 20% loss in oil pressure. Simply replacing worn bearings may fix this problem, but in older engines with a lot of wear not much can be done besides completely overhauling the engine.

    Particles in the oil can also cause serious problems with oil pressure. After oil flows through the engine, it returns to the oil pan, and can carry along a lot of debris. The debris can cause problems with the oil pickup screen and the oil pump itself. The holes in the oil pickup screen measure about 0.04 square inches (0.26 cm2). Holes of this size only pick up bigger pieces of debris and allow a lot of smaller pieces to flow through it. The holes in the screen are so big (relative to debris) because at low temperatures and slow engine speed the oil is very viscous and needs large openings to flow freely. Even with these large holes in the screen, it can still become clogged and cause low oil pressure. A .005-inch-thick (0.13 mm) coating on the screen can reduce hole size to about .03 square inches (0.19 cm2), which in turn reduces the flow of oil by 44 percent.

    Even after passing through the oil pickup screen and the oil filter, debris can remain in the oil. It is very important to change the oil and oil filter to minimize the amount of debris flowing through your engine. This harmful debris along with normal engine wear in high mileage engines causes an increase in clearances between bearings and other moving parts.

    Low oil pressure may be simply because there is not enough oil in the sump, due to burning oil (normally caused by piston ring wear or worn valve seals) or leakage. The piston rings serve to seal the combustion chamber, as well as remove oil from the internal walls of the cylinder. However, when they wear, their effectiveness drops, which leaves oil on the cylinder walls during combustion. In some engines, burning a small amount of oil is normal and shouldn’t necessarily cause any alarm, whereas burning lots of oil is a sign that the engine might be in need of an overhaul.

Oil Pumps in High Performance Engines
    Not all engines have the same oiling needs. High performance engines, for example, place higher stress on the lubricating system. In this case, the lubricating system must be especially robust to prevent engine damage.[2] Most engines in cars on the road today don’t run much past 5,000–6,000 rpm, but that isn’t always the case in performance engines, where engine speeds could reach up to 8000-9000 rpm. In engines like these, it is imperative that the oil circulates quickly enough, or air may become trapped in the oil. Also, to free up power, some engines in performance applications run lower weight oil, which requires less power to run the oil pump. Common oil weights in engines today are usually either 5w30 or 10w30 oil, whereas performance engines might use 0w20 oil, which is less viscous.